Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
This great article following next pertaining to How to Install a Bathtub Yourself is highly motivating. Don't skip it.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently easily accessible, the project can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the new tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also embeded in the brand-new one. Make sure you have certified yourself for the work as well as fit trying it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub and also don't require to change the setup of your previous water system pipelines.
Your tools and also material list should consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic due to the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will originate from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bathtub up until the level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression join; after that do the same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of a minimum of when as this will resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining frame supplied with the bath needs to be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to crack a stiff seal, triggering the water to penetrate the wall in between the bath and also the tiling, leading to issues with moisture as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can split relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is advisable to fit the ceramic tiles using waterproof or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our piece about How to Install a Bathtub Yourself. Thanks a ton for spending some time to read our blog. Are you aware of somebody else who is enthusiastic about the topic? Why not promote it. Thanks so much for taking the time to read it.
Quick, reliable, call! Report this page